BITBOX



Цена: $131.58
Software module for reading and writing Delphi ECUs internal flash memory for China vehicles with diesel engines.China Delphi DCM3.7AP (FID: 145) This ECU is based on MCU Renesas SH72513 with internal flash memory 2.0 Mb. Allows reading and writing by OBD2 with checksumm correction on writing.

Цена: $87.72
Module for OBD virtual reading and writing with CAN-bus Toyota Delphi Gen1 ECUs used in Toyota and Scion petrol vehicles.Toyota Delphi MPC565/SH72xx (FID: 140)Module supports 3 types of Delphi ECUs based on different MCUs: Motorola MPC565, Renesas SH72544 & SH72512Supported filesize: 1Mb, 1.5Mb, 2MbModule allows:- Software identification- Virtual reading lastest software update- Writing (update version or downgrade)- Recovery from any stateModule supports only CANbus vehicles.

Цена: $210.53
Module for OBD virtual reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen1 ECUs used in Toyota/Lexus/Scion/Hino petrol and diesel vehicles.Toyota Denso NEC 76F00XX (FID: 24)Toyota Denso NEC TCM 76F00XX (FID: 26) - testIt supports working with ECM and TCM of Denso ECUs with CAN-bus and based on MCUs NEC 76F0038, 76F0039, 76F0040, 76F0070 и 76F0085.Module allows:- Software identification- Virtual reading lastest software update- Writing (update version or downgrade)- Checksums and CVN correction- Recovery from any state** This feature allows to recovery ECU broken (with any tool) during CANBus writing or while Techstream update. You don't need any NBD/JTAG device, it CAN BE DONE with J2534 device via CANBus with bootstrap mode. This feature allows easy recovery of ECUs, including LC200 4.5TD without hard opening of the case and neccessary access to back side of PCB, and also new ECUs without NBD/JTAG pins on PCB (for example Camry V50, Highlander 3.5 U50, etc.).

Цена: $210.53
Module for OBD reading/virtual reading and writing Toyota Denso newGen ECUs used in Toyota&Lexus petrol and diesel vehicles. Checksum correction included.Module supports 2 protocols types:TYPE 1 (FID: 23, 27)Allowed FullFlash READING and WRITING Toyota&Lexus petrol vehicles with 2.0 6ARFSE, 2.0T 8ARFTS, 1.2T 8NRFTS, 3.5 2GRFKS, 3.5 7GRFSE etc. engines via P5-CAN-bus.Engine MCU D76F0199GD 1280KbEngine MCU D76F0196F1 1536KbEngine MCU D76F0219F1 2048KbTransmission MCU D76F0199GD 1280KbTransmission MCU D76F0196F1 1536KbAlso this FID allows to set READ PROTECTION PATCH which will disable ECU reading and will protect your MOD files from stole.Supported vehicles:Lexus NX 200t AGZ1#Lexus IS 200t ASE30Lexus GS 200t ARL10Lexus RX 200t AGL2#Lexus RC 200t ASC10Lexus ES 200 ASV61Toyota Auris 1.2t NRE185Toyota Camry 2.0 ASV51Toyota Crown 2.0tToyota Tacoma 3.5 GRN3##Lexus GS 350 GRL1#Lexus RX 350 GGL2#Toyota Highlander 2.0t ASU5#Toyota C-HR 1.2t NGX##Supported engines:2.0 6AR-FSE2.0 8AR-FTS1.2 8NR-FTS3.5 2GR-FKS3.5 7GR-FSE3.5hyb 8GR-FXS1.8hyb 2ZR-FXEetc...TYPE 2 (FID: 28)Allowed FullFlash VIRTUAL READING and WRITING with CS and CVN correction for Toyota&Lexus diesel and NA petrol vehicles with 2.8TD 1GDFTV, 2.4TD 2GDFTV, 4.0 1GRFE, 2.7 2TRFE, 2NRFE, 3ZRFAE engines. Writing possible ONLY if we have file for your vehicle on our server.We will not respond to the claims about the inability to read a file from our server if we do not have it. Supported files list can be found here.Engine MCU D76F0199GD 1280KbEngine MCU D76F0196F1 1536KbEngine MCU D76F0219F1 2048KbSupported vehicles:Toyota C-HR ZGX10LToyota HiLUX GUN##Toyota LC150 Prado GDJ##, GRJ15#Toyota Tacoma TRN2##Toyota Yaris 1.5 NSP151Lexus RC-F USC10Lexus GS-F URL10Lexus RX450h GYL2#Supported engines:2.8TD 1GDFTV2.4TD 2GDFTV4.0 1GRFE2.7 2TRFE5.0 2URGSE1.5 2NRFE2.0 3ZRFAE2.5 2ARFEetc...

Цена: $210.53
Module for OBD reading and writing with CAN-bus Toyota Denso and Fujitsu Ten Gen3 ECUs used in Toyota/Lexus petrol and diesel vehicles with new Dynamic Force engines.Toyota Denso Gen3 R7F701202 (FID: 149)Supports Denso ECUs based on MCU Renesas R7F701202 with 4Mb flash memory.Module allows:- Software identification- Reading- Writing with checksumm correction- Recovery after any failSupported vehicles:Lexus ES250 ES300h (ZA10, ZH10)Lexus LS500 (F5)Lexus UX200, UX200h (X10)Toyota Auris/Corolla 2.0, 2.0hyb (E21)Toyota Avalon 2.5hyb (XH5)Toyota Camry 2.5, 2.5hyb (VA70, VH70)Toyota C-HR 2.0 (X10)Toyota Crown 2.0hyb (SH20)Toyota RAV4 2.0, 2.0hyb (A50)Toyota HiLUX 2.4TD in test modeetc...Supported engines:2.0 M20AFKS2.0hyb M20AFXS2.5 A25AFKS2.5hyb A25AFXS2.5hyb A25BFXS3.5turbo V35AFTS2.4TD 2GDFTV - testetc...Attention! Diesel Toyota vehicles with Denso Gen3 ECUs have limited support. Toyota HiLUX 2.4TD is supported in test mode. HiACe is not supported. Will be add as soon as it possible.

Цена: $745.61
Package of 5 modules with discount for Toyota/Lexus/Scion/Hino vehicles.Package includes:- Toyota Denso Gen1 CAN- Toyota Denso Gen2/newGen CAN- Toyota Denso Gen3 CAN- Toyota Delphi Gen1 CAN- Toyota Gen1 Virtual Reader

Цена: $105.26
Service module for identification and virtual reading Toyota, Scion, Lexus and Hino Denso and Delphi Gen1 ECUs with NEC MCUs 76F0004/15/23/38/39/40/70/85 and Motorola MPC565 .It allows to get ID of the firmware through OBD connector with any J2534 adapter and if this firmware available on our server You can download it for FREE.Toyota Gen1 ECM Virtual reader (FID: 8)Toyota Denso Gen1 TCM Virtual reader (FID: 9)Toyota Denso Gen1 HCM Virtual reader (FID: 22)Attention! We are not provide WRITING. U can use this module for stock files getting for acquaintance.Our base is now contains 4700+ files.Attention! We are not provide ORI files by mail, skype etc. You have to use this module to get file in the car.We will not respond to the claims about the inability to read a file from our server if we do not have it.Denso newGen (Gen2) files 1.25, 1.5 and 2.0 Mb available only for owners of Toyota Denso newGen CAN module.Attention! This module will not allowed to use with Slave dongles.

Цена: $210.53
Модуль для чтения и записи блоков управления, устанавливаемых на дизельные автомобили корейских марок Kia/Hyundai.Kia/Hyundai Denso Diesel SH72546 (FID: 42)Блок управления работает на базе процессора Renesas SH72546 с внутренней флеш памятью 3.75Mb.Позволяет виртуальное чтение и запись FullFlash по CAN-bus с коррекцией контрольных сумм. Восстановление возможно из любого состояния.Поддерживаемые авто:Hyundai Grand Starex H-1 (TQ) 2.5 CRDI Euro6Hyundai H350 (EU) 2.5 CRDI Euro6Hyundai H100 Porter (HR) 2.5 CRDI Euro6Kia Bongo/K2500 2.5 CRDI Euro6Kia/Hyundai Delphi DCM6.2AP (FID: 41) - тестБлок на базе процессора MCU NXP SPC5674 с внутренней флеш памятью 4Mb.Позволяет читать и писать область калибровок по CAN-bus с коррекцией чексумм. Восстановление возможно из любого состояния.Поддерживаемые авто:Hyundai i20 (GB) 1.1 CRDI Euro6Kia Rio (UB) 1.1 CRDI Euro6Kia/Hyundai Delphi DCM3.7AP (FID: 39)Блок на базе процессора Renesas SH72513 с внутренней флеш памятью 2Mb.Позволяет чтение FullFlash и запись области калибровок по CAN-bus с коррекцией чексумм.Поддерживаемые авто:Hyundai H-1 (TQ) 2.5 CRDi Euro4/5Hyundai i20 (PB) 1.1 CRDi Euro5Hyundai i20 (PB) 1.4 CRDi Euro4/5Hyundai i30 (GD) 1.4 CRDi Euro5Hyundai iX20 (JC) 1.4 CRDi Euro5Hyundai H100/Porter (HR) 2.5 CRDi Euro5Kia Rio (UB) 1.1 CRDi Euro5Kia Rio (UB) 1.4 CRDi Euro5Kia Cee'd (JD) 1.4 Euro5Kia Venga (YN) 1.4 CRDi Euro5Kia Bongo/K2500 (PU) 2.5 CRDI Euro5Kia Delphi DCM3.2AP (FID: 37)Блоки управления работают на базе процессора Motorola MPC563 с внешней флеш-памятью AM29BDD160GB с суммарным адресным пространством 2.5Мб.Доступно чтение FullFlash, запись по CAN-bus, коррекция чексумм.Поддерживаемые авто:Kia Bongo 2.9 CRDI Euro4Kia Carnival 2.9 CRDI Euro4Kia Sedona 2.9 CRDI Euro4

Цена: $175.44
Модуль для чтения и записи блоков управления Kefico CPGDSH2.2x.x/CPEGD2.20.x, устанавливаемых на бензиновые автомобили корейских марок Kia и Hyundai.Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)Данные типы блоков работают на базе процессора Infineon Tricore TC1782 с внутренней флеш памятью 2.5Mb.Поддерживаются блоки: CPEGD2.20.1, CPEGD2.20.2, CPEGD2.20.3, CPEGD2.20.4, CPGDSH2.26.1, CPGDSH2.24.4.Позволяет чтение FullFlash и запись области калибровок по CAN-шине с коррекцией контрольных сумм.Внимание! На некоторых автомобилях комплектация не позволяет работу через диагностический разъем. В этом случае необходимо работать с блоком на столе, вскрытия блока не требуется, подключение делается напрямую к пинам разъема ЭБУ.Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x BSL (FID: 253)Данные типы блоков работают на базе процессора Infineon Tricore TC1782 с внутренней флеш памятью 2.5Mb.Позволяет чтение и запись FullFlash в режиме BSL. Требуется вскрытие блока и подключение согласно инструкции.

Цена: $175.44
Module for reading and writing through the diagnostic connector Renault diesel vehicles with Continental ECUs.Renault Siemens SID301 (FID:157)This FID is for working with Continental SID301 ECUs based on MPC561 with external flash memory 2.0Mb.Allows reading and writing with checksumm correction by CANbus.Renault Continental SID305 (FID:155)This FID is for working with Continental SID305 ECUs based on Infineon Tricore TC1766 with internal flash memory 1.46Mb.Allows reading and writing with checksumm correction by CANbus.Renault Continental SID310 (FID:177)This FID is for working with Continental SID310 ECUs based on Infineon Tricore TC1791 with internal flash memory 4.0Mb.Allows reading and writing with checksumm correction by CANbus.Attention! Module is in test stage. New ECU types will be added ASAP.

Цена: $307.02
Module for reflashing through OBD2 connector by CAN-bus Bosch ECUs used in BMW Exx vehicles. No need to dismount, open or drill an ECU - FULL OBD2 solution.Allows VIRTUAL reading and writing of calibration area.Module is now supports:Bosch EDC17CP45 (DDE7.3.1)Bosch EDC17CP02 (DDE7.1)Bosch EDC17C06 (DDE7.0)Bosch EDC17CP09 (DDE7.3)Bosch EDC17C41 (DDE7.2.1)Bosch EDC17C50 (DDE7.0.1)Bosch MEVD17.2Bosch MEVD17.2.6Bosch MEVD17.2.9Other ECU types will be added as soon as possible.We will not respond to the claims about the inability to read a file from our server if we do not have it.

Цена: $789.47
Package of all 3 modules we have for BMW with discount. BMW Bosch Exx CAN + Fxx Bosch ENET + Fxx/Gxx Bosch MG1/MD1 ENET.

Цена: $307.02
Модуль для работы через диагностический разъем по Ethernet с блоками управления Bosch, устанавливаемые на автомобили BMW F-серии. Не требует снятия, вскрытия или сверления блока!

Цена: $307.02
Module for reflashing through OBD2 connector by Ethernet for Bosch ECUs used in diesel BMW Fxx vehicles. No need to dismount, open or drill an ECU - FULL OBD2 solution.Warning! Module doesn’t work with J2534 adapter, BMW ENET-to-OBD2 cable is required for work. Also this family can’t work on the bench!Module allows:• Identification• Virtual Reading• Writing program and maps• CS and CVN fix on writing• Recovery with original file (as official BMW diagnostic system)• Reading and writing coding data• DTC reading / clearingSupported diesel ECUs:• Bosch EDC17C41 (DDE7.2.1)• Bosch EDC17C50 (DDE7.0.1)• Bosch EDC17C56 (DDE7.4.1)• Bosch EDC17CP45 (DDE7.3.1)• Bosch EDC17CP49 (DDE7.5.1)• Bosch EDC17CP09 (DDE7.3a)Supported petrol ECUs:• Bosch MEVD17.2• Bosch MEVD17.2.4• Bosch MEVD17.2.5• Bosch MEVD17.2.6• Bosch MEVD17.2.9• Bosch MEVD17.2.G (incl. S55)• Bosch MEVD17.2.8• Bosch MEVD17.2.H• Bosch MEVD17.2.3We will not respond to the claims about the inability to read a file from our server if we do not have it.

Цена: $307.02
Module for reflashing through OBD2 connector by Ethernet for Bosch MG1 and MD1 ECUs used in BMW Fxx and Gxx vehicles.Supports Bosch ECUs based on MCU NXP MPC5777 with 7.5Mb of main flash memory and Infineon Aurix TC298 with 8Mb memeory.BMW Fxx/Gxx Bosch MG1 MPC5777 ENET (FID: 160)BMW Fxx/Gxx Bosch MD1 MPC5777 ENET (FID: 161)BMW Fxx/Gxx Bosch MG1 TC298 ENET (FID: 162) [TEST]Module allows:Software identificationVirtual reading from serverReading if file not found in server (not for all SW versions)Writing with checksumm and CVN correctionDTC read and clear

Цена: $307.02
Модуль для работы через диагностический разъем по Ethernet с блоками управления Bosch MG1 и MD1, устанавливаемые на автомобили BMW F и G-серии.

Цена: $148.15
Модуль для чтения и записи через диагностический разъем блоков управления коробок передач Siemens GS20 и Bosch GS8.60.2, устанавливаемых на автомобили BMW.

Цена: $140.35
Module for reading and writing via diagnostic connector TCM Siemens GS20 and Bosch GS8.60.2 used on BMW vehicles.Bosch GS8.60.2 (FID: 3)This type of TCM is set to BMW vehicles equipped with Automatic transmission models of ZF 5HP24. Supports to read calibration area, writing and correction checksum through the diagnostic connector.BMW E38 735BMW E38 740BMW E38 730dBMW E39 535BMW E39 540Siemens GS20 (FID: 4)ECU Siemens GS20 installed on the BMW with boxes of General Motors 5L40. Supports read/write field calibration with automatic correction checksums through the diagnostic connector.BMW E38 730dBMW E39 530dBMW E39 525dBMW E53 X5 3.0d

Цена: $175.44
Модуль для чтения и записи через диагностический разъем мотоциклов марки BMW Motorrad с блоками управления Bosch и Magneti Marelli.Bosch M9.2 (BMSK) (FID: 171)Bosch ME9.2.0 (BMSKP) (FID: 172)Marelli MBC1 (BMS-E) (FID: 170)Bosch ME17.2 (BMS-X) - в разработкеMarelli MBC2 (BMS-E2B) - в разработкеKeihin (KMS) - в разработкеСтоимость модуля будет увеличиваться по мере добавления поддержки новых типов блоков.

Цена: $210.53
Software module to work with Bosch MSE3.0 and US6.0/MSE6.0 engine control units. Allows you to identify the software version, virtual read files from our server and to write calibration area with automatic correction checksums on writing.Bosch MSE3.0 (FID: 6, 78)ECU is based on MCU ST10F275 with internal memory area 832Kb. Allows Virtual Reading and Writing with CS fixing. If we have no file on server it is possible to read in BSL mode with FID:78.Bosch MSE6.0/US6.0 (FID: 79)ECU is based on MCU SPC563M64 with internal memory area 1.5Mb. Allows Virtual Reading and Writing with CS fixing. If we have no file on server u have to send ECU to our office for reading and adding to server. Work is possible on the BENCH only in case that there is no CANbus in diagnostic plug.

Цена: $122.81
Software module for reading and writing Bosch ECUs internal flash memory for China vehicles with petrol engines.Bosch ME7.9.7 (FID: 68) with C167 1Mb VR/W/CSBosch M7.8 (FID: 57) with ST10F275 832Kb VR/W/CSBosch ME7.8.8 (FID: 63) with ST10F275 832Kb K-line VR/W/CSBosch ME7.8.8 (FID: 76) with ST10F275 832Kb CAN VR/W/CSBosch ME17.8.8 (FID: 60) with Infineon TC1728 1.5Mb R/W/CSBosch ME17.8.8 Saic (FID: 127) with Infineon TC1728 1.5Mb R/W/CSBosch ME17.8.8 Vantage (FID: 166) with Infineon TC1728 1.5Mb R/W/CSBosch ME17.8.8.1 (FID: 82) with Infineon TC1728 1.5Mb R/W/CSBosch ME17.8.8.1 Geely (FID: 84) with Infineon TC1728 1.5Mb R/W/CSBosch MED17.8.10 Haval (FID: 122) with Infineon TC1728 1.5Mb R/W/CS /TEST/BYD TB10 Type1 (FID: 81) with Renesas SH72531 1.25Mb R/W/CSBYD TB10 Type2 (FID: 148) with Renesas SH72531 1.25Mb VR/W/CSBosch M7.8/ME7.8.8 BSL (FID: 75) with ST10F275 832Kb K-line R/CS** - adapter BITS001 required. Tested only with J2534 Tactrix Openport 2.0

Цена: $122.81
Software module for reading and writing Delphi ECUs internal flash memory for China vehicles with petrol engines.Delphi MT20U (FID: 51) with Motorola MC912DT128 128Kb - R/W/CSDelphi MT20U2 (FID: 59) with Motorola MC9S12KG256 256Kb - R/W/CSDelphi MT22.1 (FID: 52) with Motorola MC9S12XEP768 768Kb - R/W/CSDelphi MT22.1 IAC (FID: 158) with Motorola MC9S12XEQ512 512Kb - R/W/CSDelphi MT22U (FID: 53) with Motorola MC9S12XET256 256Kb - R/W/CSDelphi MT20UED (FID: 58) with Motorola MC9S12KG256 256Kb - R/W/CSDelphi MT22.1.1 HW1 (FID: 54) with Motorola MC9S12XET256 256Kb - R/W/CSDelphi MT34 (FID: 55) with Infineon Tricore + EXT.Flash 1Mb - R/W/noCS - testDelphi MT62.1 K-line (FID: 56) with NXP SPC5634 1.5Mb - R/W/noCSDelphi MT62.1 CAN (FID: 146) with NXP SPC5634 1.5Mb - R/W/noCSDelphi MT80 (FID: 61) with Infineon Tricore TC1762 1.5Mb - R/W/CSDelphi MT92/MT92.1 (FID: 86) with Infineon Tricore TC17xx 2Mb/2.5Mb - R/W/noCS - test

Цена: $87.72
Software module for reading and writing Siemens/Continental ECUs internal flash memory for China vehicles with petrol engines.Continental Simos 9.5 (FID: 83)ECU Simos 9.5 is based on MCU C167 with external flash memory 512 Kb. It allows to virtual read fullflash, write calibration area via CANbus and checksumm correction on writing.

Цена: $307.02
КАБЕЛЬ для программирования в комплекте позволяет: • Идентификацию • Виртуальное чтение • Запись с коррекцией чексумм и CVN • Восстановление с оригинальным заводским файлом • Чтение и запись кодинга • Чтение и стирание ошибок Поддерживаемые типы блоков для дизельных авто: • Bosch EDC17C41 (DDE7.2.1) • Bosch EDC17C50 (DDE7.0.1) • Bosch EDC17C56 (DDE7.4.1) • Bosch EDC17CP45 (DDE7.3.1) • Bosch EDC17CP49 (DDE7.5.1)   Поддерживаемые типы блоков для бензиновых авто: • Bosch MEVD17.2.4 • Bosch MEVD17.2.5 • Bosch MEVD17.2.6 • Bosch MEVD17.2.9 • Bosch MEVD17.2.G (в том числе для двигателей S55) • Bosch MEVD17.2.8 /test/ • Bosch MEVD17.2.H /test/

Цена: $210.53
Module for OBD/Bench working with Continental M3C ECUs used in different moto/extreme vehicles.Allows software identification, FullFlash reading and writing by CANbus, CS calculation of calibration area and EEPROM area.Following families are present:Arctic Cat Continental M3C 9S12XE (FID:194)BRP Continental M3C 9S12XE (FID:193)Ducati Continental M3C 9S12XD (FID:191)Ducati Continental M3C 9S12XE (FID:192)KTM/Husqvarna Continental M3C 9S12XE (FID:196)Beta/Kymco/Sherco/Stels/TGB Continental M3C 9S12XE (FID:195)Attention! Readed file contains virtual EEPROM with mileage info, VIN, keys etc... Make sure that you will make MOD file based on file you read. Module is also suitable for cloning.Attention! Module is garanteed works with all listed ECUs on the BENCH. OBD working is also possible if vehicle has no any systems that will interrupt connection - f.e. in BRP it is dashboard and power steering wheel. U will need to disconnect that systems or work on the BENCH.

Цена: $210.53
Module for reading and writing through the diagnostic connector by CAN-bus for diesel Chrysler/Dodge/Jeep and Fiat vehicles with Bosch ECUs.FCA Bosch EDC17C49 (FID: 106)Engine control unit is based on MCU Infineon Tricore TC1797 with internal flash memory 4.0 Mb.Module allows virtual reading and writing of calibration area by OBD2 with checksumm correction on writing.FCA Bosch EDC17C79 (FID: 107)Engine control unit is based on MCU Infineon Tricore TC1797 with internal flash memory 4.0 Mb.Module allows virtual reading and writing of calibration area by OBD2 with checksumm correction on writing.FCA Bosch EDC17CP27 (FID: 108)Engine control unit is based on MCU Infineon Tricore TC1797 with internal flash memory 2.0 Mb.Module allows virtual reading and writing of calibration area by OBD2 with checksumm correction on writing.FCA Bosch EDC17C49/C79 Reader (FID: 124)Allows real reading of calibration area on the BENCH by CANbus with checksumm checking. Needs if virtual reader cannot fnd file for your vehicle.

Цена: $263.16
Module for reading and writing through the diagnostic connector by CAN-bus Chrysler/Dodge/Jeep and Fiat petrol vehicles with Motorola NGC3, NGC4, NGC4A and Continental GPEC, GPEC2 ECUs.Also its possible to work on the bench with no openning ECU.Module allows to Identify, Read FullFlash, Write calibration area and automatically correct CheckSums on writing.Motorola NGC3 MPC565 1Mb (FID: 12)Motorola NGC4 MPC5554 2Mb (FID: 13)Motorola NGC4A MPC5554 2Mb (FID: 15)Continental GPEC (SIM90) MPC561+EXT.FLASH 2Mb (FID: 16)Continental GPEC2 MPC5566 3Mb (FID: 14)** - for vehicles till 2014. Newer cars have ECUs with RSA LOCK and need to be UNLOCKED before writing. This new ECUs need to use with module FCA Petrol Gen2 CAN If you are not sure about what ECU you have to work please contact sales department before ordering.

Цена: $263.16
Software module for OBD2 working with FCA group vehicles (Chrysler/Dodge/Jeep/Fiat) with ECUs Continental GPEC2 LOCKED, GPEC2A, GPEC3.This ECUs are used on normal aspirated petrol cars from 2013 and have internal protection from tuning (LOCK).For success MOD file writing it needs to remove protection (ECU Unlock) in BSL mode. You will need to open ECU and connect it on the bench as shown in connection manual.This is the world first solution with no need to send ECU to any workshop for PCM modification. All you can do by yourself.Module allows this operations:Identification and getting LOCK status (LOCKED/ UNLOCKED)OBD2 FULLFLASH readingOBD2 EEPROM readingECU Unlock in BSL modeOBD2 Calibration area writingOBD2 EEPROM writingRead and clear DTCAt this moment we support this ECU types:Continental GPEC2 2013+ MPC5566 3Mb (FID: 20)Continental GPEC2 2015+ MPC5566 3Mb (FID: 21)Continental GPEC2A MPC5674 4Mb (FID: 19)Continental GPEC2A 2018+ MPC5674 4Mb (FID: 131)Continental GPEC3 MPC5674 4Mb (FID: 18)Attention! UNLOCK function is not working now with all J2534 adapters. Currently we tested and guarantee correct unlock with Scanmatik SM2, Scanmatik SM2-PRO, CarDAQ Plus, Bosch VCM2, Mongoose (excl. ISO).Unlock does not work with Tactrix OpenPort 2.0, Chipsoft J2534, SMS Soft Dialink.

Цена: $175.44
Module for reading and writing through the diagnostic connector Ford petrol vehicles with Bosch MG1 ECUsFord Bosch MG1CS015 TC277 (FID: 180)This FID is for working with Bosch MG1CS015 ECUs based on Infineon Aurix TC277 with internal flash memory 4Mb.Allows reading and writing with checksumm correction by CANbus.Ford Bosch MG1CS018/MG1CS019 TC298 (FID: 181)This FID is for working with Bosch MG1CS018 and MG1CS019 ECUs based on Infineon Aurix TC298 with internal flash memory 8Mb.Allows reading and writing with checksumm correction by CANbus.Bosch MG1CS016 and Bosch MG1CS017 ECUs are in development and will be add ASAP.

Цена: $175.44
FIDs: 255, 256, 257, 259, 260, 261, 262, 263, 279Модуль для чтения и записи флеш-памяти блоков управления Continental, устанавливаемых на дизельные автомобили Ford.Работа возможна при подключении через диагностический разъем или на столе.Ford Continental SID206 (FID: 259)Семейство поддерживает работу с блоками Continental SID206 на базе MPC561 с внешней флеш памятью 2 Мб.Позволяет чтение и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Continental SID208 (FID: 255)Семейство поддерживает работу с блоками Continental SID208 на базе процессора Infineon TC1797 с внутренней флеш памятью 4 Мб.Позволяет чтение FullFlash и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Continental SID209 [TEST] (FID: 279)Семейство поддерживает работу с блоками Continental SID209 на базе процессора Infineon TC1797 с внутренней флеш памятью 4 Мб.Позволяет чтение FullFlash и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Continental SID211 (FID: 256)Семейство поддерживает работу с блоками Continental SID211 на базе процессора Infineon TC1791 с внутренней флеш памятью 4 Мб.Позволяет чтение FullFlash и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Continental SID803 (FID: 260)Семейство поддерживает работу с блоками Continental SID803 на базе процессора MPC561 с внутренней флеш памятью 448Кб.Позволяет чтение и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Continental SID803A (FID: 261)Семейство поддерживает работу с блоками Continental SID803A на базе процессора MPC561 с внешней флеш памятью 2 Мб.Позволяет чтение и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Continental SID807EVO (FID: 257)Семейство поддерживает работу с блоками Continental SID807EVOна базе процессора TC1797 с внутренней флеш памятью 4 Мб.Позволяет чтение и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Continental SID802 (FID: 263)Семейство поддерживает работу с блоками Continental SID802 базе процессора C167 с внешней флеш памятью 512Кб.Позволяет чтение и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Continental SID804 (FID: 262)Семейство поддерживает работу с блоками Continental SID804 базе процессора C167 с внешней флеш памятью 512Кб.Позволяет чтение и запись области калибровок. Коррекция чек-сумм делается при записи

Цена: $175.44
Модуль для чтения и записи по CAN-шине флеш-памяти блоков управления Continental, устанавливаемых на бензиновые автомобили Ford.Ford Continental EMS2101/2103 C167+Ext.Flash 1MB CAN - R/W/CSFord Continental EMS2102 C167+Ext.Flash 512KB CAN - R/W/CSFord Continental EMS2204 TC1738 2MB CAN - VR/W/CS/VBF to BINFord Continental EMS2205 TC1766 1.46MB CAN - VR/W/CS/VBF to BINFord Continental EMS2207 TC1738 2MB CAN - VR/W/CS/VBF to BINFord Continental EMS2208 TC1767 2MB CAN - VR/W/CS/VBF to BINFord Continental EMS2211 TC1738 2MB CAN - VR/W/CS/VBF to BINFord Continental EMS2213/EMS2214/EMS2215 TC1738 2MB CAN - VR/W/CS/VBF to BINFord Continental EMS2301/EMS2302 TC1724 1.5MB CAN - R/W/CSFord Continental EMS24xx TC1791 4MB CAN - VR/W/CS/VBF to BINFord Continental EMS2510/EMS2511 TC1791 4MB CAN - VR/W/CS/VBF to BINFord Continental EMS2701 TC1791 4MB CAN - VR/W/CS/VBF to BINСемейства с виртуальным чтением поддерживают запись c обновлением, также можно декриптовать VBF файлы с помощью кнопки VBF to BIN в программе BitBox. Для каждого семейства при декрипте файл будет проверен на совместимость с выбранным семейством!

Цена: $140.35
Модуль для чтения и записи по CAN-шине флеш-памяти блоков управления Delphi , устанавливаемых на дизельные автомобили Ford.Ford Delphi DCM3.5 (FID: 301)Семейство поддерживает работу с блоками Delphi DCM3.5 на базе процессора MPC5566 с внутренней флеш памятью 3Мб.Позволяет чтение и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Delphi DCM6.1 (FID: 302)Семейство поддерживает работу с блоками Delphi DCM6.1 на базе процессора TC1797 с внутренней флеш памятью 4Мб.Позволяет чтение и запись области калибровок. Коррекция чек-сумм делается при записи.Ford Visteon DCU-10x/DCU-20x (FID: 318)Семейство поддерживает работу с блоками Visteon DCU- 101/102/104/201 на базе процессора ST10F276 с внутренним адресным пространством 896Кб.Позволяет идентификацию ПО, чтение и запись по КАН-шине. Коррекция чек-сумм делается при записи.

Цена: $307.02
Module for reading and writing through OBD2 connector by CAN-bus ACDelco Gen1 ECUs used in petrol GM vehicles.GM ACDelco E38 (FID: 96)ECU is based on MCU Motorola MPC561 with external flash memory 2.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.Reading/writing time about 3-5 minutes!GM ACDelco E39 (FID: 100)ECU is based on MCU Motorola MPC5566 with internal flash memory 3.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.Reading/writing time about 3-5 minutes!GM ACDelco E39A (FID: 97)ECU is based on MCU Motorola MPC5566 with internal flash memory 3.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.Reading/writing time about 3-5 minutes!GM ACDelco E67 (FID: 99)ECU is based on MCU Motorola MPC565 with external flash memory 2.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.Reading/writing time about 3-5 minutes!GM ACDelco E78 (FID: 94)ECU is based on MCU Motorola MPC5566 with internal flash memory 3.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.Reading/writing time about 3-5 minutes!GM ACDelco E80 (FID: 102)ECU is based on MCU Motorola MPC5676 with internal flash memory 6.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.GM ACDelco E83 (FID: 91)ECU is based on MCU Motorola MPC5565 with internal flash memory 2.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.Reading/writing time about 3-5 minutes!GM ACDelco E92 (FID: 98)ECU is based on MCU NXP SPC5674 with internal flash memory 4.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.Reading/writing time about 3-5 minutes!New ECU type will be added as soon as possible!

Цена: $307.02
Module for reading and writing through OBD2 by CAN-bus ACDelco Gen2 ECUs used in petrol GM vehicles.GM ACDelco E39A Gen2 (FID: 129)ECU is based on MCU Motorola MPC5566 with internal flash memory 3.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.GM ACDelco E80 Gen2 (FID: 176)ECU is based on MCU NXP MPC5676 with internal flash memory 6.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.GM ACDelco E82 Gen2 (FID: 168)ECU is based on MCU NXP SPC5676 with internal flash memory 6.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.GM ACDelco E84 Gen2 (FID: 167)ECU is based on MCU NXP SPC5676 with internal flash memory 6.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.GM ACDelco E92 Gen2 (FID: 128)ECU is based on MCU NXP SPC5674 with internal flash memory 4.0Mb.Allows to read fullflash and write calibration area through CAN-bus with checksumm correction on writing.New ECU types will be added as soon as possible!

Цена: $175.44
Module for reading and writing through OBD2 connector by CAN-bus ECUs used in diesel GM vehicles (Opel, Chevrolet, Saab, Holden).GM Bosch EDC16C39 HW1 (FID: 65)ECU is based on MCU Motorola MPC562 with external flash memory 2.0Mb.Allows to read and write calibration area through CAN-bus with checksumm correction on writing.Supported vehicles:Chevrolet Captiva 2.0 VCDIChevrolet Cruze 2.0 VDCIChevrolet Epica 2.0 VCDIChevrolet Lacetti 2.0 VCDIDaewoo Winstorm 2.0 VCDIOpel Antara 2.0 CDTIOpel Astra (H) 1.9 CDTIOpel Combo (D) 1.6 CDTIOpel Signum 1.9 CDTIOpel Vectra (C) 1.9 CDTIOpel Zafira (B) 1.9 CDTIGM Bosch EDC16C39 HW2 (FID: 67) - Bench OBD onlyECU is based on MCU Motorola MPC562 with external flash memory 2.0Mb.Allows to read and write calibration area through CAN-bus on the bench with checksumm correction on writing.Supported vehicles:Chevrolet Trailblazer II 2.8TD DuramaxHolden Colorado 2.8TD DuramaxGM ACDelco E87 (FID: 90)ECU is based on MCU Motorola MPC5565 with internal flash memory 2.0Mb.Allows to read and write calibration area through CAN-bus with checksumm correction on writing.GM ACDelco E98 (FID: 85)ECU is based on MCU Motorola SPC5674 with internal flash memory 4.0Mb.Allows to read and write calibration area through CAN-bus with checksumm correction on writing.

Цена: $175.44
Module for OBD reading and writing Harley-Davidson motorbikes with Delphi ECUs.HD Delphi MT05 CAN (FID:30) is based on the MCU NXP MC9S12XEP768 with internal flash memory 768Kb.HD Delphi VooDoo CAN (FID:43) is based on the MCU NXP MC9S12DG128 with internal flash memory 128Kb.

Цена: $140.35
Модуль для чтения и записи по CAN-шине блоков управления Transtron, устанавливаемых на дизельные автомобили Isuzu. Поддерживаются блоки на базе процессоров SH7058, SH7059 и SH725xx.Isuzu Transtron SH7058/SH7059/SH72533/SH72544 CAN (FID:280)Семейство для работы с блоками Transtron на базе процессоров Renesas SH7058/SH7059/SH72533/SH72544 с внутренней флеш-памятью 1Mb/1.5Mb/2Mb/2.5Mb.Поддерживает идентификацию, чтение с автоопределением размера, запись и коррекцию КС.

Цена: $175.44
Module for reading and writing in BSL mode for Continental SIM2K-250/251/253/258/260/261 ECUs used in petrol Kia and Hyundai vehicles.Continental SIM2K-25x TC1782 BSL (FID: 150, 152)ECU series Siemens SIM2K-250/251/253/258/259 with MCU Infineon Tricore TC1782 onboard have internal flash memory 2.5Mb.FID:150 allows reading and writing of calibration area in BSL mode. ECU needs to be opened. Checksum and CVN correction performs on writing. Also it have "Remove protection" feature to UNLOCK OBD2 writing.FID:152 allows to write modified files by OBD2 for UNLOCKED with FID:150 ECUs.Continental SIM2K-26x TC1791 (FID: 151)Continental SIM2K-260 and SIM2K-261 based on MCU Infineon Tricore TC1791 onboard have internal flash memory 4Mb.FID allows reading and writing of calibration area in BSL mode. ECU needs to be opened. Checksum and CVN correction performs on writing.Continental SIM2K-250/251 TC1767 (FID: 152) - in developmentAttention! Special power adapter BITS001 required. Tested only with J2534 Tactrix Openport 2.0, DrewTech CarDAQ.

Цена: $210.53
Module for OBD reflash for ECUs used in diesel Kia/Hyundai vehicles with Delphi and Denso ECUs.Kia/Hyundai Denso Diesel SH72546 (FID: 42)ECU based on MCU Renesas SH72546 with internal memory 3.75Mb.Allows to virtual read and write FullFlash via CAN-bus with CHK calculation. Recovery is possible from any state.Supported vehicles:Hyundai Grand Starex H-1 (TQ) 2.5 CRDI Euro6Hyundai H350 (EU) 2.5 CRDI Euro6Hyundai H100 Porter (HR) 2.5 CRDI Euro6Kia Bongo/K2500 2.5 CRDI Euro6Kia/Hyundai Delphi DCM6.2AP (FID: 41) - testECU based on MCU NXP SPC5674 with internal memory 4Mb.Allows to read and write calibration area via CAN-bus with CHK calculation. Recovery is possible from any state.Supported vehicles:Hyundai i20 (GB) 1.1 CRDI Euro6Kia Rio (UB) 1.1 CRDI Euro6Kia/Hyundai Delphi DCM3.7AP (FID: 39)ECU based on MCU Renesas SH72513 with internal memory 2Mb.Allows to read FullFlash and write calibration area via CAN-bus with CHK calculation.Supported vehicles:Hyundai H-1 (TQ) 2.5 CRDi Euro4/5Hyundai i20 (PB) 1.1 CRDi Euro5Hyundai i20 (PB) 1.4 CRDi Euro4/5Hyundai i30 (GD) 1.4 CRDi Euro5Hyundai iX20 (JC) 1.4 CRDi Euro5Hyundai H100/Porter (HR) 2.5 CRDi Euro5Kia Rio (UB) 1.1 CRDi Euro5Kia Rio (UB) 1.4 CRDi Euro5Kia Cee'd (JD) 1.4 Euro5Kia Venga (YN) 1.4 CRDi Euro5Kia Bongo/K2500 (PU) 2.5 CRDI Euro5Kia Delphi DCM3.2AP (FID: 37)ECU based on MCU Motorola MPC563 +external flash AM29BDD160GB with total memory adress area 2.5Mb.Allows to read FullFlash, write with CHK calculation by CAN-bus.Supported vehicles:Kia Bongo 2.9 CRDI Euro4Kia Carnival 2.9 CRDI Euro4Kia Sedona 2.9 CRDI Euro4

Цена: $175.44
Module for reading and writing for Kefico CPGDSH2.2x.x/CPEGD2.20.x ECUs used in petrol Kia and Hyundai vehicles.Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x (FID: 251)This ECU types are based on MCU Infineon Tricore TC1782 with internal flash memory 2.5Mb.Supported ECUs: CPEGD2.20.1, CPEGD2.20.2, CPEGD2.20.3, CPEGD2.20.4, CPGDSH2.26.1, CPGDSH2.24.4Allows reading fullflash and writing of calibration area through CAN-bus with checksum correctionAttention! Some vehicles have complectation that does not allow to work by OBD2 plug. In this case please use bench connection for reading and writing.Kia/Hyundai Kefico CPGDSH2.2x.x/CPEGD2.20.x BSL (FID: 253)This ECU types are based on MCU Infineon Tricore TC1782 with internal flash memory 2.5Mb.Allows fullflash reading and writing with checksum correction in BSL-mode.

Цена: $175.44
Module for reading and writing through CAN-bus by diagnostic OBD2 plug ECUs used in petrol Kia and Hyundai vehicles.Kefico CPEGD2.20.1/CPGDSH2.26.1 (FID: 70)Supported Kefico CPEGD2.20.1 and CPGDSH2.26.1 ECUs are based on MCU Infineon Tricore TC1782 with internal flash memory 2.5Mb.Allows reading and writing calibration area through CAN-bus with checksum correction. Recovery is possible from any state.Bosch ME(G)17.9.1x (FID: 72)ECU series Bosch ME(G)17.9.11/12/13 is based on MCU Infineon Tricore TC1762 with internal flash memory 1.46Mb.Allows reading and writing FullFlash through CAN-bus with checksum correction.Supported vehicles:Kia/Hyundai 1.0-1.6 MPI/DOHCBosch ME(G)17.9.21 (FID: 74)ECU series Bosch ME(G)17.9.21 is based on MCU Infineon Tricore TC1724 with internal flash memory 1.5Mb.Allows reading and writing FullFlash through CAN-bus with checksum correction.Bosch ME(D)(G)17.9.8 (FID: 73)ECU series Bosch ME(D)(G)17.9.8 is based on MCU Infineon Tricore TC1767 with internal flash memory 2.0Mb.Allows reading and writing FullFlash through CAN-bus with checksum correction.Siemens SIM2K-47 (FID: 88)ECU Siemens SIM2K-47 is based on MCU С167 with external flash memory 512Kb.Allows reading and writing FullFlash through CAN-bus with checksum correction.Siemens SIM2K-24x (FID: 93)ECU series Siemens SIM2K-240/241/242/245 is based on MCU Infineon Tricore TC1764 with internal flash memory 2Mb.Allows reading and writing FullFlash through CAN-bus with checksum correction.Siemens SIM2K-141/341 (FID: 104)ECU series Siemens SIM2K-141/341 is based on MCU Motorola MPC561 with external flash memory 2Mb.Allows reading and writing FullFlash through CAN-bus with checksum correction.Siemens SIM2K-141.1 (FID: 144)ECU series Siemens SIM2K-141.1 is based on MCU Motorola MPC563 with external flash with total memory size 2.5Mb.Allows virtual reading and writing through CAN-bus with checksum correction.Delphi MT86 (FID: 77)ECU Delphi MT86 is based on Tricore TC1766 with internal flash memory 1.46Mb.Allows reading and writing calibration area through CAN-bus with checksum correction.

Цена: $175.44
Module for OBD reading and writing with CAN-bus Denso ECUs used in Mazda diesel vehicles with SkyActiv-D engines.Mazda Denso Diesel Gen3 (FID: 246) with SH72543 2.0Mb - R/W/CSMazda Denso Diesel Gen3 Crypto (FID: 242) with SH72543 2.0Mb - R/W/CSMazda Denso Diesel Gen3 Crypto (FID: 245) with SH72546 3.75Mb - R/W/CSMazda Denso Diesel Gen4 (FID: 238) with MPC5746 4.0Mb - R/W/CS

Цена: $210.53
Module for OBD reading and writing with CAN-bus Denso and Mitsubishi ECUs used in Mazda petrol vehicles with SkyActiv-G engines.Mazda Denso Gen3 D02 (FID: 244) with SH72543 2.0Mb - R/W/CSMazda Denso Gen3 D03 (FID: 243) with SH72543 2.0Mb - R/W/CSMazda Denso Gen4 D08 (FID: 249) with MPC5746 4.0Mb - R/W/CSMazda Denso Gen4 D11 (FID: 247) with MPC5746 4.0Mb - VR/W/CSMazda Mitsubishi Gen3 M03/M04 (FID: 240) with MH8501 2.0Mb - R/W/CSMazda Mitsubishi Gen3 M09 (FID: 243) with MH8501 2.0Mb - R/W/CSMazda Mitsubishi Gen4 M13/M16 (FID: 248) with MPC5746 4.0Mb - R/W/CS

Цена: $210.53
Module for reading and writing through the diagnostic connector by CAN-bus for diesel Mercedes-Benz vehicles with Bosch EDC17 ECUs.Supported ECU types:Bosch EDC17CP01 / EDC17CP10 (FID: 200)Bosch EDC17CP57 / EDC17CP60 / EDC17C66 (FID: 201)Bosch EDC17CP46 (FID: 202)Bosch EDC17C43 (FID: 206)Bosch EDC17CP01 with no ext. flash (FID:207) /TEST/Module allows:SW identificationReading of calibration areaWriting of calibration areaCS correction

Цена: $210.53
Module for virtual reading and writing through the diagnostic connector by CAN-bus for petrol Mercedes-Benz vehicles with Bosch MED17 ECUs.Supported ECU types:MB Bosch MED17.7.1 / MED17.7.3 (FID: 205)MB Bosch MED17.7.3.1 (FID: 204)MB Bosch MED17.7.2 (FID: 203)MB Bosch MED17.7.5 (FID:215)Infiniti Bosch MED17.7.2 (FID: 208)Module allows:SW identificationVirtual Reading of calibration area (900+ files in a base)Writing of calibration areaCS correction

Цена: $175.44
Module for reading and writing through the diagnostic connector by CAN-bus for diesel Mercedes-Benz vehicles with Delphi CRD ECUs.MB Delphi CRD3.xx TC1797 (FID: 214)This FID is for working with Delphi CRD3.xx ECUs based on Infineon Tricore TC1797 with internal flash memory 4 Mb.Allows reading and writing with checksumm correction by CANbus.MB Delphi CRD3.xx TC1793 (FID: 197)This FID is for working with Delphi CRD3.xx ECUs based on Infineon Tricore TC1793 with internal flash memory 4 Mb.Allows reading and writing with checksumm correction by CANbus.Infiniti Delphi CRD3.xx (FID: 218)This FID is for working with Delphi CRD3.xx ECUs based on Infineon Tricore TC1797 with internal flash memory 4 Mb.Allows reading of calibration area and writing with checksumm correction by CANbus.MB Delphi CRD2.xx (FID: 217)This FID is for working with Delphi CRD2.xx ECUs based on MPC5566 with internal flash memory 3 Mb.Allows reading and writing with checksumm correction by CANbus.MB Delphi CRD.11 (FID: 216)This FID is for working with Delphi CRD.11 ECUs based on MPC563 with external flash memory with total 2.5 Mb.Allows reading and writing with checksumm correction by CANbus. If you have OBD writing issue - connect ECU on the bench.

Цена: $175.44
Module for reading and writing by CAN-bus for petrol Mercedes-Benz vehicles with Siemens/Continental SIM271 ECUs.Continental SIM271DE2.0 (FID: 209)ECU is based on MCU Infineon Tricore TC1796 with internal flash memory 2Mb.Allows reading of calibration area and writing with checksumm correction by CANbus. Full OBD2 solution.Siemens SIM271KE2.0 (FID: 213)ECU is based on MCU Infineon Tricore TC1796 with internal flash memory 2Mb.Allows reading of calibration area and writing with checksumm correction by CANbus. No need to open ECU. Full OBD2 solution.Attention! Some vehicles can have OBD2 reading issues in case of different equipment set. If u cant read with OBD2 please use bench connection.

Цена: $210.53
SW module to flash ECUs Delphi MT05 and Delphi MT05.2/3 through the diagnostic connector. It allows identification, read FullFlash and write the calibration area, as well as automatic correction checksums while writing.J2534 adapter needed (i.e. Tactrix Openport 2.0 ).Delphi MT05 (FID:2) is based on the MCU Infineon SAK-XC164CM-16F40F with internal flash memory 128Kb.Delphi MT05.2/3 (FID:1) is based on the MCU Infineon SAK-XC164CS-32F40BB with internal flash memory 256Kb.

Цена: $210.53
Module for reading and writing extrime vehicles with Rotax engines and ECUs Bosch ME17.8.5 and Siemens MSE 3.7x. Its working through diagnostic plug or on the bench with no need to open ECU.Siemens MSE 3.7x (FID: 10, 80)Siemens MSE 3.7x family allows to get software ID, read FullFlash and write calibration area by K-line (FID 10) and CANbus (FID 80), also it performes checksum correction on writing.For today we support 2 ECU types:Siemens MSE 3.7 with MCU ST10F269 and internal Flash memory 256Kb.Siemens MSE 3.71 with MCU ST10F269 and internal Flash memory 256Kb.Bosch ME17.8.5 (FID: 11, 31)Allows to get software ID, virtual reading of the FullFlash from our server and to write calibration area by CANbus. Also it performs checksum correction on writing.We will not respond to the claims about the inability to read a file from our server (Virtual reading) if we do not have it.ECU is based on MCU Infineon Tricore TC1762 with internal Flash memory 1504Kb.Rotax P-TEK (FID:199)ECU is based on MCU MC9S12D64 with internal flash memory 64Kb. Allows to get software ID, read and write calibration area by CANbus with CS calculation.

Цена: $87.72
Service module for identification and virtual reading of Arctic Cat and Suzuki Denso ECUs 32920-4xxxx based on MCU Renesas SH7052.Real ECU software reading is only possible with drilling big hole to access AUD port pins. Its not very safe for future outdoor ECU using.This module allows to get correct file with no drilling.You can get software ID through K-line and get file if we have it on our server.Arctic Cat Denso Virtual Reader (FID: 64)Suzuki Moto Denso Virtual Reader (FID: 103)Attention! We are not provide ORI files by mail, skype etc. You have to use this module to get file with the vehicle.Attention! Module does not provide writing.We will not respond to the claims about the inability to read a file from our server if we do not have it.Attention! Module activated for FREE for all users of BitEdit Arctic Cat Denso module

Цена: $87.72
Module for software identification (ID), virtual reading and writing Eldor EM 2.0 ECUs used in motobikes MV Agusta.ECU is based on MCU NXP MPC5634 with internal flash memory 1.5Mb.Supported models:BrutaleF3F4RivaleTurismo Veloce

Цена: $175.44
Модуль для чтения и записи по CAN-шине флеш-памяти блоков управления Hitachi Gen1, устанавливаемых на бензиновые автомобили Nissan/Infiniti.Nissan Hitachi SH705X/SH72XX Gen1 CAN (FID:300)Поддерживаются блоки Hitachi Gen1 на базе процессоров Renesas SH7055/SH7058/SH7059/SH72531/SH72533 и работающих по шине CAN-bus.SH705519N 512KbSH705822N, SH705828N 1024KbSH705927N 1536KbS7253131N 1280KbS7253332N 2048KbМодуль позволяет идентификацию, чтение с автоопределением размера, запись и коррекцию КС, чтение и стирание ошибок.

Цена: $175.44
Module for reflashing through OBD2 connector by CAN-bus Delphi ECUs used in Peugeot and Citroen deisel vehicles.PSA Delphi DCM6.2A (FID: 179)This ECU is based on MCU NXP MPC5674 with internal flash memory 4.0 Mb. Allows reading and writing of calibration area by OBD2 with checksumm correction on writing.PSA Bosch EDC17C10 TC1797 (FID: 210)ECU is based on MCU Infineon Tricore TC1797 with internal flash memory 4.0 Mb. Allows reading and writing of calibration area by OBD2 with checksumm correction on writing.PSA Bosch EDC17C10 TC1796 (FID: 211)ECU is based on MCU Infineon Tricore TC1796 with external flash memory 4.0 Mb. Allows reading and writing of calibration area by OBD2 with checksumm correction on writing.

Цена: $175.44
Module for OBD reading and writing Delphi ECUs used in SsangYong diesel vehicles.SsangYong Delphi DCM6.2AP (FID: 32)ECU based on MCU NXP SPC5673 with internal memory 3Mb.Allows to read and write calibration area via CAN-bus with CHK calculation. Recovery is possible from any state.Supported vehicles:SsangYong Tivoli/XLV D16DTFSsangYong Rodius/Stavic II D22DTRSsangYong Korando C/New Actyon D22DTFSsangYong Rexton G4 D22DTRSsangYong Delphi DCM6.2AP-6D (FID: 89)ECU based on MCU NXP SPC5674 with internal memory 4Mb.Allows to read and write calibration area via CAN-bus with CHK calculation. Recovery is possible from any state.Supported vehicles:SsangYong Rexton G4 D22DTR-SCRSsangYong Delphi DCM3.7AP (FID: 33)ECU based on MCU Renesas SH72513 with internal memory 2Mb.Allows to read FullFlash and write calibration area via CAN-bus with CHK calculation.Supported vehicles:SsangYong Actyon Sports D20DTRSsangYong Korando C/New Actyon D20DTFSsangYong Rexton D20DTRSsangYong Rodius D20DTRSsangYong Stavic II D20DTRSsangYong Delphi DCM3.2AP (FID: 35)ECU based on MCU Motorola MPC563 +external flash AM29BDD160GB with total memory adress area 2.5Mb.Allows to read FullFlash, write with CHK calculation by K-line.Supported vehicles:SsangYong Actyon D20DT Euro4SsangYong Actyon Sports D20DT Euro4SsangYong Kyron D20DT Euro4SsangYong Kyron D27DT Euro4SsangYong Rexton D20DT Euro4SsangYong Rexton D27DT Euro4SsangYong Rodius D27DT Euro4SsangYong Delphi DCM3.1 (FID: 34)ECU based on MCU Motorola MPC555 with internal memory 448Kb.Allows to read FullFlash and write calibration area via K-line with CHK calculation.Supported vehicles:SsangYong Actyon D20DT Euro3SsangYong Actyon Sports D20DT Euro3SsangYong Kyron D20DT Euro3SsangYong Kyron D27DT Euro3SsangYong Rodius D27DT Euro3Tata Safari 3.0 DiCORTata Xenon 3.0 DiCOR

Цена: $175.44
Module for OBD reading and writing Siemens ECUs used in SsangYong petrol vehicles.Siemens SIM2K-410 (FID: 40)Engine control unit Siemens SIM2K-410 based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.This ECU is used on SsangYong petrol vehcles with 1.6 G16DF engine. Allows virtual reading and writing of FullFlash by OBD2 with checksumm correction on writing.Supported vehicles:SsangYong Tivoli 1.6 G16DFSsangYong Tivoli XLV 1.6 G16DFSiemens SIM2K-C201 (FID: 45)Engine control unit Siemens SIM2K-C201 based on MCU Infineon Tricore TC1767 with internal flash memory 2.0 Mb.This ECU is used on SsangYong petrol vehcles with 2.0 G20DF engine. Allows reading and writing of FullFlash by OBD2 with checksumm correction on writing.Supported vehicles:SsangYong Korando/New Actyon 2.0 G20DF

Цена: $175.44
Модуль для работы с лодочными моторами Suzuki на базе блоков управления Mitsubishi.FID 198: Suzuki Marine Mitsubishi MH8104F K-LineПозволяет идентификацию, чтение и запись FullFlash по К-линии, проверку и коррекцию КС. Поддерживает:Suzuki Marine DF9.9B/15A/20ASuzuki Marine DF25A/30ASuzuki Marine DF40A/50A/60ASuzuki Marine DF100A/115A/140AДругие типы блоков и моторов будут добавлены по возможности.Внимание! Модуль требует подачи напряжения +16В для разрешения программирования. Напряжение берется с 12-го пина адаптера J2534 или с внешнего источника питания. Адаптер J2534 должен поддерживать однобайтные операции по К-линии и установку+16В на 12 пин. Проверен и работает OpenPort 2.0. DrewTech Mongoose, Scanmatik, Ford VCM2 не работают с данным модулем.

Цена: $263.16
Module for reading and writing by CAN-bus Delphi DMCI ECUs used in DAF and Hyundai trucks.ECU is based on MCU Motorola MPC561 with internal flash memory 2.0Mb.Allows to read and write calibration area through CAN-bus with checksumm correction on writing.DAF Delphi DMCI (FID: 117)Hyundai Delphi DMCI (FID: 118)

Цена: $264.08
Module for reading and writing through OBD2 connector by CAN-bus Delphi ETC3 ECUs used in trucks DAF, Tatra, Kenworth, Peterbilt, Hyundai.DAF/Industrial Delphi ETC3 (FID: 220)This FID is for working with Delphi ETC3 ECUs based on MCU NXP MPC5566 with internal flash memory 3 Mb.Allows reading of calibration area and writing with checksumm correction by CANbus.Hyundai Delphi ETC3 (FID: 221) /TEST/This FID is for working with Delphi ETC3 ECUs based on MCU NXP MPC5566 with internal flash memory 3 Mb.Allows reading of calibration area and writing with checksumm correction by CANbus.

Цена: $350.88
Module for reading and writing through OBD2 connector by CAN-bus Bosch EDC17CV41 ECUs used in trucks/industrial vehicles Tata-Daewoo, New Holland, CASE, CLAAS, Iveco, Doosan.ECU is based on MCU Infineon Tricore TC1797 with internal flash memory 4.0Mb.Allows to read and write calibration area through CAN-bus with checksumm correction on writing.Iveco Bosch EDC17CV41 (FID: 110)Tata-Daewoo Bosch EDC17CV41 (FID: 112)CASE/New Holland Bosch EDC17CV41 (FID: 113)CLAAS Bosch EDC17CV41 (FID: 114)Doosan Bosch EDC17CV41 (FID: 115)Tigercat Bosch EDC17CV41 (FID: 116)Pi Makina Bosch EDC17CV41 (FID: 119)Ford Bosch EDC17CV41 (FID: 109)Hino Bosch EDC17CV41 (FID:147) - testAttention! Some of supported vehicles are using 24V voltage onboard. Please use J2534 adapters with 24V support or connect ECU on the bench.New ECU types will be added as soon as possible!

Цена: $87.72
Module for reading and writing Magneti Marelli ECUs, used on the VAG normal aspirated vehicles with 1.6 CFNA, CFNB, CLRA, CLSA, 1.4 CGGB, CLPA, CLPB and 1.6 CFZA engines.Magneti Marelli IAW 7GV (FID: 5)This ECU is based on MCU Infineon SAK-XC2785X-104F80L with internal flash memory 832Kb.Allows to read FullFlash and write calibration area by OBD2. Supports 1.6 CFNA, CFNB, CLRA, CLSA and 1.4 CGGB, CLPA, CLPB engines.It writes calibration area and takes only 3 minutes.Also we are recommend calibration Editor for Marelli IAW 7GV.Magneti Marelli IAW 7GVE (FID: 71)This ECU is based on MCU Infineon SAK-XC2xxx with internal flash memory 832Kb.Allows to read FullFlash and write calibration area by OBD2.Supports 1.4 CGGB engines.Magneti Marelli IAW 9GV (FID: 7)This ECU is based on MCU NXP SPC5634 with internal flash memory 1.5 Mb.Used in FlexFuel VAG vehicles with 1.6 CFZA engine.Allows to read and write FullFlash in BSL mode, checksumm correction and EEPROM reading and writing.ECU must be opened and connected on the bench as shown in instruction manual.Attention! Marelli 9GV is not working now with all J2534 adapters. Currently we tested and guarantee correct work with CarDAQ Plus, Bosch VCM2, Mongoose.Also we are recommend calibration Editor for Marelli IAW 9GV.Magneti Marelli IAW 4HV (FID: 17)This ECU type is using on VAG vehicles with 1.4 BUD, BXW, CGGA, CGGB petrol engines. Allows to read FullFlash and write of calibration area by K-Line.ECU is based on MCU ST10F296 with internal adress space 832 Kb.

Цена: $175.44
Module for reading and writing on the Bench through CAN-bus for diesel and petrol Volvo vehicles with Denso SH72xxx ECus.Removing ECU required but opening not need, only direct CAN connection to ECU.Volvo Denso SH72543 2Mb BENCH-CAN (FID: 143)Volvo Denso SH72546 3.75Mb BENCH-CAN (FID: 142)Module supports FullFlash reading and writing and CS fix on writing.

Цена: $175.44
Module for OBD2/Bench reading and writing with CAN-bus for Denso ECUs based on Renesas SH7058 and SH7059 MCU.Denso SH7058/SH7059 (FID: 153)Allows FullFlash reading and writing with CS correction.Supported vehicles: Nissan, Mitsubishi, Subaru, Mazda, Opel, Hyundai TrucksIn test stage: Hino, Suzuki, Volvo, KubotaAttention!Some vehicles has no CANbus wiring in OBD2 plug. Some has gateway that do not allow to work bootloader. In this cases please use BENCH connection to work with ECU.Some trucks and industrial vehicles has +24V onboard - please be sure you J2534 adapter support this voltage.

Цена: $263.16
Module for reflashing Honda Marine Outboard engines with Keihin ECUs.Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.Supports ECUs with part numbers 34750-XXX-XXX.Following families are present:Honda Marine Keihin K-Line Reader (FID:229)Honda Marine Keihin M32R 256KB (FID:228)Attention! Some of ECUs can require external programming voltage to start writing. If this ECU type will be detected automatically, BitBox will ask you to perform some actions - it is possible on the BENCH only. Please check manual and YouTube video for details.

Цена: $263.16
Module for reflashing Honda motorbikes, scooters, ATVs and other extreme vehicles with Keihin ECUs.Allows software identification, FullFlash reading and writing by K-line, CS calculation, eeprom reading and writing, recovery from any states.Supports ECUs with part numbers 38770-XXX-XXX.Following families are present:Honda Moto Keihin K-Line Reader (FID:175)Honda Moto Keihin M32R/SPC 256KB (FID:125) - R/W/CSHonda Moto Keihin H8C 32/56KB (FID:126) - R/W/CSHonda Moto Keihin SPC 512KB (FID:174) - R/W/CSHonda Moto Keihin SH7058 1MB (FID:227) - R/W/CSHonda Moto Keihin R8C 32/48/64/96/128KB (FID:226) - VR/W/CSAttention! Some of ECUs can require external programming voltage to start writing. If this ECU type will be detected automatically, BitBox will ask you to perform some actions - it is possible on the BENCH only. Please check manual and YouTube video for details.Other ECU types will be add ASAP.

Цена: $122.81
Module for reading and writing through the diagnostic connector Renault petrol vehicles with different ECUs.Renault Continental EMS3110 (FID:139)This FID is for working with Continental EMS3110 ECUs based on Infineon Tricore with internal flash memory 1.46Mb.Allows reading and writing with checksumm correction by CANbus.Renault Continental EMS3125 (FID:165)This FID is for working with Continental EMS3125 ECUs based on Infineon Tricore TC1782 with internal flash memory 2.5Mb.Allows reading and writing with checksumm correction by CANbus.Renault Continental EMS3155 (FID:178)This FID is for working with Continental EMS3155 ECUs based on Infineon Tricore TC1782 with internal flash memory 2.5Mb.Allows reading and writing with checksumm correction by CANbus.Renault Valeo V40/V42 (FID:154)This FID is for working with Valeo V40 and V42 ECUs based on Renesas SH7058 with internal flash memory 1Mb.Allows reading and writing with checksumm correction by CANbus.Renault Valeo V50 (FID:169)This FID is for working with Valeo V50 ECUs based on Renesas SH72543 with internal flash memory 2Mb.Allows reading and writing with checksumm correction by CANbus.Other ECU types are in development and will be add ASAP.

Цена: $30.00
BMW E-NET сканер - это оборудование для кодирования и программирования автомобилей BMW F - серии через Ethernet (RJ45) разъем вашего ПК.BMW ENET работает с программой E-SYS, ISTA, Rheingold и поддерживает диагностику всех электронных систем в автомобиле, позволяет читать / стирать / расшифровывать коды неисправностей, проводить адаптацию и программирование электронных блоков, а также просматривать параметры датчиков в реальном времени.Возможности BMW ENET:Автоматическая идентификация автомобиляОпределение параметров блоков управленияСчитывание кодов ошибокРасшифровка кодов ошибокСтирание кодов ошибокПросмотр параметров в реальном времениТест исполнительных механизмовАктивация / деактивация инженерных функцийАктивация исполнительных механизмовПрограммирование блоков управленияВедомый поиск неисправностейПоддерживаемые авто:1-series: F20, F21, F44, F45, F462-series: F22, F233-series: F30, F31, F34, F80, G204-series: F32, F33, F35, F36, F82, F835-series: F07, F10, F11, F18,G306-series: F06, F12, F137-series: F01, F02, F03, F04X-series: F15, F16, F25, G02i3: I01i8: I12M-series: F80, F82, F83, F10, F06, F12, F13, F15Alpina F-series variants: D3, B3, B4, XD3, D5, B5, B6, B7Mini: F55, F56.

Цена: $120.00
Беспроводной BMW E-NET сканер - это оборудование для кодирования и программирования автомобилей BMW F - серии через Wifi вашего ПК.BMW ENET работает с программой E-SYS, ISTA, Rheingold и поддерживает диагностику всех электронных систем в автомобиле, позволяет читать / стирать / расшифровывать коды неисправностей, проводить адаптацию и программирование электронных блоков, а также просматривать параметры датчиков в реальном времени.Возможности BMW ENET:Автоматическая идентификация автомобиляОпределение параметров блоков управленияСчитывание кодов ошибокРасшифровка кодов ошибокСтирание кодов ошибокПросмотр параметров в реальном времениТест исполнительных механизмовАктивация / деактивация инженерных функцийАктивация исполнительных механизмовПрограммирование блоков управленияВедомый поиск неисправностейПоддерживаемые авто:1-series: F20, F21, F44, F45, F462-series: F22, F233-series: F30, F31, F34, F80, G204-series: F32, F33, F35, F36, F82, F835-series: F07, F10, F11, F18,G306-series: F06, F12, F137-series: F01, F02, F03, F04X-series: F15, F16, F25, G02i3: I01i8: I12M-series: F80, F82, F83, F10, F06, F12, F13, F15Alpina F-series variants: D3, B3, B4, XD3, D5, B5, B6, B7Mini: F55, F56.

Цена: $25.00
Security dongle - this is device that connects through USB port and makes the identification of the user and activated licenses. It is necessary part of our software and buying once and for all/any software module.We are currently using the most modern and small version of the key SenseLock EL-Genii with built-in internal memory of 64 KB.

Leave your number and we will call you back as soon as possible